Hydraulic Rams

OTC 4449 Air Wedge Lockout Tool Air wedge is designed to create working room around the window frame when using other lockout tools. Description: Adjustable inflation and release valve provides versatile use.

OTC 4452 Master Lockout Tool Set Set includes: • Lock Knob Puller • Slide Lock Linkage Hook • Under Window Knob Puller • Under Window Lock Button Depressor • Under Window Slide Lock Puller • Lockout Wedge • Porsche Lock...

OTC 4450 Lockout Tool Set, 6pc Set Includes: • Lockout Wedge • Lock Knob Hook • Slide Lock Linkage Hook • Toyota/Chrysler Key Hole Lever • Vent Window Lever Puller • Bell Crank Thin Bar • Instruction Manual

OTC 4489 Trim Fastener and Molding Removal Set Trim Fastener and Molding Removal Set Features: Set includes five different sizes and styles of tools that allow easy removal of trim fasteners, moldings, and wheel hubs. Tools are made of plastic to...

OTC 4448 DOOR BUZZER SHUTOFF TOOL 2 PCS This simple tool allows for work with the vehicle door open without the annoying door buzzer on. The high tension spring can be placed in the door jamb to close the door buzzer switch typically found by the...

OTC 4460 Electrical Connector Separator Tool (2 piece) Releases locking tabs on electrical connectors, component connections and wiring harness connectors. Eliminates damage to the tab or connector. This pair of tools permits access to...

OTC 4493 Stinger Angle-tip Relay Pliers Designed to remove and install relays, which are usually located in confined, hard-to-reach areas.  Specially coated tips offer a solid grip on the relay.  

OTC 4492 4 pc. E-Clip Tool Set 5-Piece E-Clip Tool Set Features: Dual operation tool: one end of tool releases e-clip; other end of tool installs e-clip. Tools fit four sizes of e-clips: 6 mm, 7 mm, 8 mm, and 9 mm. Each tool easily locks into handle...

OTC 4401 Tube Bending Pliers Bends tubing from the side allowing for use in limited access areas.   3/16" and 1/4" diameter tubing

OTC 4472 3-IN-1 SOLDER TOOL  DESCRIPTION: The OTC 4472 3-in-1 Cordless Solder Tool is the professional choice when soldering, shrinking or spot torching is required. Variable heat control quickly generates up to 480° C (900°F) of...

OTC 4467 Automatic Wire Stripper Quick removal of insulation on wire AWG 12-20. Comes with adjustable depth gauge (8mm to 12mm). Sharp v-shaped tooth easily removes insulation without any damage to soft wire strands.   Cutting tool stored...

OTC 4468 9" Self Adjusting Wire Stripper Strips insulating sheathing from wires ranging from 10 ga. to 22 ga.  Easy-to-use, just insert wire and squeeze. Also cuts and crimps.

OTC 4477 3/8" Cable Cutter Perfect choice for cutting heavier copper and aluminum cables. This tool is especially valuable for battery service where replacing a terminal is required. Clean cut with minimal mushing of wire strands.

OTC 4508 Stinger Oil/Grease Seal Puller Professional Style Seal Puller Designed to remove oil and grease seals when servicing cars, SUVs, and light trucks without damaging the housing or bearing. Hook tips in two sizes and professional handle design...

OTC 4421 Pilot Bearing Puller Attachment Removes pilot bearings, thrust washers, and smaller bearings hidden in a shaft or housing. Features: Jaws require a minimum of 5/8" opening and can range up to a max of 1-1/2" diameter. Min/Max Reach is 1/8" to...

OTC 4420 Pilot Bearing Pulling Attachment Use to pull a pilot bearing from the end of the crankshaft. Features: Interchangeable jaws. One set of jaws covers a spread of 1/2" to 1-1/2". Other set of jaws covers a spread of 3/8" to 1-3/8". Both sets of...

OTC 4422 Pilot Bearing Puller Use to pull a pilot bearing from the end of the crankshaft. Features: A restriction plate catches the bridge and prevents the jaws from spinning when force is engaged. The "Tee Handle" design is easy-to-use and eliminates...

OTC 4523 Offset Hose Clamp Pliers Head is offset from handle to allow access to hard-to-reach clamps. Features: Swivel jaws allow pliers to be used on many different flat-band and ring-type hose clamps.

OTC 4525 Flexible Hose Clamp Pliers Description: Allows technician to access the flat-type hose clamps located in hard-to-reach areas. • Pliers has locking mechanism to hold clamp in the open position, making removal and installation of clamp easier...

OTC 4441 HD 3 Leg Oil Filter Wrench Large Description: • Self-gripping design for true universal fit from 4" to 6 1/2" • Heavy duty knurled leg design for extra grip and strength • 1/2" square drive